ServSmartServSmartStart free
Featuring DECO Products sealers

Paver Sealer Calculator: How Much Sealer to Buy and What to Charge

Square feet in, buckets and a job price out. Works with any sealer's label coverage rate.

Area

Sealer

SilaCast BES · 160–200 sq ft/gal on pavers · up to 240 on stamped · 1 coat

Penetrating, joint-stabilizing paver sealer.

Not for raw / bare concrete. Porous pavers land at the low end.

Surface

Typical uses the low end of DECO's range for a safe estimate. Porous block can take more than twice the sealer.

Coats & waste

Coats
1
Waste
10%

You need

Enter the square footage to see gallons.

SilaCast BES: 160 sq ft/gal per coatCoverage figures per DECO product data sheets — always confirm on the current product label.

Your rate × the measured square footage — the quick quote.

Typical: $0.90–$1.50 per sq ft. Use any rate.
Job price$0.00Enter sq ft + your rate
Product cost—Add a price per bucket above to fill this in, or type it.
Profit—Price − product cost

Enter or measure the square footage above.

How the calculator works

  1. Area × coats gives the square feet of sealing you'll actually apply.
  2. Divide by the sealer's coverage rate (sq ft per gallon, per coat) to get gallons.
  3. Add a waste allowance, 10% by default, for overspray, edges and thirsty spots.
  4. Round up to whole 5-gallon buckets, because that's how sealer is sold.
Gallons = square feet × coats ÷ coverage × (1 + waste %)

Coverage rates by sealer

Coverage for DECO Products sealers, in square feet per gallon per coat. Smooth, dense pavers reach the high end. New, porous or rough pavers sit at the low end, so the calculator starts there.

SealerCoverageDefault coats
SilaCast BES160–240 sq ft/gal1
TravaCast300–400 sq ft/gal1
Shine-A-Cast240–280 sq ft/gal1
Ure-a-Cast 1K (estimated)300 sq ft/gal1
Deco 20 Clear Finish175–375 sq ft/gal1
Salt Shield 303175–375 sq ft/gal2

Coverage figures per DECO product data sheets — always confirm on the current product label.

How to price a paver sealing job

  • Per square foot: the calculator suggests $0.90–$1.50 per sq ft as a starting point. Use your own market rate.
  • Labor + margin: material cost plus your hours at your hourly rate, with your margin on top.
  • Target profit: for big or multi-day jobs, start from what you want to clear per day and work backwards to the price.

Common questions

How much paver sealer do I need for 1,000 square feet?

It depends on the sealer's coverage rate. At 160 sq ft per gallon, one coat on 1,000 sq ft takes about 6.9 gallons with 10% waste, so two 5-gallon buckets. A sealer that covers 300 sq ft per gallon needs about 3.7 gallons, one bucket. Enter your numbers above for the exact count.

How many coats of paver sealer should I apply?

Follow the product label. Most sealers in this calculator default to one coat, Salt Shield 303 defaults to two, and Deco 20 Clear Finish goes on once. The calculator sets each product's default and lets you change it.

How much extra sealer should I buy for waste?

The calculator adds 10% by default. Raise it for very porous or rough pavers, lots of edges and borders, or sprayer overspray.

Can I use a sealer that isn't listed?

Yes. Pick Other / custom product and type the coverage rate from its label or data sheet.

Can I save or share a calculation?

Yes. The page link updates as you type, so bookmarking it or sending it to someone reopens the same numbers.

Is the calculator free?

Yes. No login and no email needed.